AMS 4345, 7150 Aluminum T7751, Extrusion 7150 Al-Alloy
STEELMAX Metal Story

 

AMS 4345 재질은 Solution Heat Treated, 응력풀림 (stress relieved) and
과시효 (overaged)된 압출 알루미늄 합금, bars, rods, shapes, tubings 규격입니다.

AMS 4345 금속은 UNS No. A97150, Aluminum Alloy 7150 재질과 대응되며
높은 내식성과 강도는 다른 7××× series 기계적성질 보다 좋습니다.

AMS 4345 재질의 높은 기계적 성질과 높은 비강도 (比强度 :strength to density ratio)
항공기용 부품과 강도와 함께 가벼움이 필요한 곳에 사용됩니다.

Alloy 7150 Temper T77511 은 bars, rods, shapes, tubings — AMS 4345
Alloy 7150 Temper T7751 은 plate 제품에 대한 AMS 4252 규정입니다.

※ Alloy Temper 77511 의 Temper T7××× — Solution Heat Treated Then Stabilized.
Applies to products that are stabilized to carry them beyond the point of maximum
strength to provide control of some special characteristics

※ Extrusion (압출 : 押出)
Shaping metal into a chosen continuous form by forcing it
through a die of appropriate shape.

금속재료를 일정한 다이에 힘을 가하며 통과시켜 연속적으로
원하는 형상의 제품을 제조하는 방법

※ Overaging (과시효 : 過時效)
An aging generated at a higher temperature, or when maintained
for a longer time, than the temperature and time where properties
of hardness, strength or the like become the highest.

※ Stress Relieving(old name : stress relief annealing : 응력제거 어닐링(풀림)
Every piece of steel has an amount of internal stress caused
by steel production, machining, surface finish, heat treatment
and other processes.
During a heat treatment process the yield strength is reduced
to a lower level. If precision parts or complicated tools with
close tolerances, this deformation could cause problems.
In the case after rough machining and stress relieving is done
with a high degree of machining allowance.
After this process the internal stress is reduced by the parts deforming.
The standard process is slow heating up to 550~650℃, holding for
minimum 2 hours and finishing with a slow cooling in the furnace.

모든 철강재는 생산, 가공, 표면 마무리, 열처리와 기타 공정진행에서
내부 응력이 어느정도 쌓일 수 밖에 없고, 이런 내부 응력을 해소시키려고
적당한 온도로 가열하고 균열화한 후, 적절한 온도로 냉각함으로써
실질적인 조직의 변화 없이 내부 응력을 줄이고자 시행하는 열처리를 말합니다.

 

Alloy 7150, UNS A97150
Chemical composition (%) Silicon (Si) 0.12 max.
Iron (Fe) 0.15 max.
Copper (Cu) 1.9~2.5
Manganese (Mn) 0.10 max.
Magnesium (Mg) 2.0~2.7
Chromium (Cr) 0.04 max.
Zinc (Zn) 5.9~6.9
Zirconium (Zr) 0.08~0.15
Titanium (Ti) 0.06 max.
Other each 0.05 max.
Other total 0.15 max.
Aluminum (Al) remainder

 

 

Alloy 7150 T77511, UNS A97150, AMS 4345
Diameter (mm) Direction Tensile strength (MPa) 0.2% Yield strength (MPa) El. (%)
0.1~6.34 L 594 545 7
LT 566 510 7
6.34~12.69 L 608 573 8
LT 573 531 8
12.70~~19.04 L 615 580 9
LT 580 552 9
19.05~50.80 L 622 587 8
LT 580 545 8

 

 

AMS

AMS 4345, 7150 Aluminum T7751, Extrusion 7150 Al-Alloy

 

스틸맥스는 연구소 수준의
깊이 있는 철강에 대한 이해를 바탕으로,

Carbon Steel, Special Steel, Stainless, Functional steel,
Ni-Alloy, Cu-Alloy, Al-Alloy, Ti-Alloy, Forging.

Plate, Sections, H-BEAM, Angle, Channel,
Flat, Round Bar, Rail, Pipe & Tube, SMLS,

ASTM, ASME, AISI-AMS, ANSI, API, SAE, AS, CSA
DIN-EN , KS, JIS, DNV, ABS, GL, LR, KR, NK. RINA, RS, CCA, IACS의

국가규격, 국제단체 규격, 국제협회 규격부터
Mill Maker Standards까지 공급하고 있습니다.

Citius, Altius, Fortius,
더 빠르게, 더 높이, 더 강하게가 요구되는올림픽처럼

공급이 어려운 철강재 공급에는
진정한 전문 선수를 필요로 합니다.

 구매, 문의, 견적, 안내가 필요하신 경우
Contact us 바로가기 : https://steelmax.co.kr/contact/